LOD 400 metal deck shop drawings, built from the model.

Consac delivers fabrication-ready roof and floor deck BIM models and coordinated shop drawings in Tekla and Revit: layouts, openings, pour stops, closures, fastening and weld details, all set to your BIM execution plan.

Steel beam Concrete topping (composite floor) Puddle welds at supports
0 Level of Development for every sheet
0 Platforms: Tekla & Revit
0 Detail families modeled, not drawn
0 Drawings generated from the model

Build a deck bay and see what we model

Switch the layers on and off, then change the profile and sheet length. This is the same set of items our LOD 400 deck models carry on every project.

Sheet length20 ft
0Sheets in this bay
0Weld points
0Rib depth (in)
0Rib pitch (in)

Illustrative bay. Final quantities come from your drawings and the engineer of record.

What LOD 400 means for metal deck

Level of Development describes how complete and reliable the model is. Pick a level to compare what the deck model contains.

Why fabrication-level deck models pay off

Deck is installed fast and cut on site when it does not fit. Resolving openings, closures and edges in the model first removes that guesswork.

Field issues by modeling level

Coordination clashes caught over project phases

Where deck detailing hours go

Typical turnaround by deck area

Chart figures are illustrative planning benchmarks for this page. Replace them with Consac project data before publishing.

What is in the package

Deck layouts

Sheet-by-sheet layout for roof and floor deck, with direction, span, laps and end bearing shown at each support.

Openings and penetrations

Mechanical, plumbing and shaft openings placed from coordinated models, with framing and edge conditions noted.

Pour stops and edge forms

Slab edge angles, gauge and height by condition, with dimensions tied to slab thickness and camber.

Closures and flashing

Cell closures, ridge and valley plates, and girder fillers modeled where the profile meets steel and walls.

Fastening and welds

Puddle welds, screws and sidelap fasteners scheduled by zone, with spacing and pattern per the engineer’s notes.

Coordinated shop drawings

Sheets, bundles, marks and bills of material cut straight from the model for submittal, fabrication and erection.

How we work

Kickoff

Read the BIM execution plan, LOD matrix and model origin.

Model

Build deck in Tekla and Revit from structural and architectural models.

Coordinate

Run clash checks with MEP and steel, then issue RFIs.

Submit

Issue shop drawings and take review comments.

Release

Deliver approved drawings, schedules and as-built updates.

Tekla and Revit, one coordinated deck model

Tekla carries the detailed deck and connections for fabrication and cutting. Revit carries the coordinated design model so architects and engineers can review. We keep both aligned to the same grid, levels and naming standard from your BIM execution plan.

Estimate your deck package

Enter the deck area to see a planning estimate of sheets and drawing sheets. For a firm price, send us your drawings.

Deck area60,000 sf
0Deck sheets (3 ft x 20 ft)
0Shop drawing sheets
0Working days, first issue
0Fastening points

Planning estimate only. Based on 5% waste, 1 drawing sheet per 2,500 sf and simple production rates.

Keywords we cover

LOD 400 metal deck metal deck shop drawings steel deck detailing composite floor deck roof deck layout pour stop details deck closures Tekla deck modeling Revit deck modeling BIM execution plan deck weld details deck openings

Questions we hear on deck projects

What is LOD 400 for metal deck?

LOD 400 is a fabrication-level model. Each deck sheet, lap, closure, pour stop, opening, fastener pattern and weld is modeled with exact size, location and type, so the shop and field can build from it.

Can you follow our BIM execution plan?

Yes. We read the plan before modeling and match the LOD matrix, naming, origin, grids, file exchange and issue cycle it calls for.

Which software do you use?

Tekla Structures for detailing and Autodesk Revit for coordination and design review, with IFC or native exchange as the plan requires.

Do you handle both roof and floor deck?

Yes. Roof deck, composite floor deck and form deck, including slab edges, openings and ceiling or wall interfaces.

What do you need to start?

Structural and architectural drawings or models, the deck specification, the BIM execution plan, and any MEP opening information.

🍪 We Use Cookies

To improve your experience, we use cookies. By continuing, you agree to our Cookie Policy & Privacy.